19/12/2016

Practical 3: Phase Diagram (Part A)

Title: Determination of Phase Diagram for Ethanol/Toluene/Water 

System Theory Three-Component Systems

Date of Practical
10 November 2016

Objective
  •  To determine the limit solubility of water and two other liquids which are ethanol and toluene (methylbenzene) in a ternary system
  •  To construct a phase diagram of ethanol/toluene/water system

Introduction

In system containing three components but only 1 phase, the degree of freedom will be four which are temperature, pressure, and the concentration of two or the three components. The degree of freedom, F can be calculated using the formula (phase rule) given:

F = C - P + 2

Where,

C = the number of components
P = the number of phases present




In the above diagram, it shows the ternary diagram. The three apexes representing a 100% pure composition and they are labelled A, B, and C. By referring to diagram below, the nearest to the head of the red arrow indicates 100% of A while the farthest from A represents 0% of A. Other values besides 0% and 100% can be indicated by the line between 0% to 100%. The right side of the triangle will be the scale for the percent abundance of A component.



Point B located at the left side apex of the triangle. The apex indicates 100% of B component. The AC line will be the base line for B. The scale of the percentage abundance of B will be at the left side of the triangle.

Point C on the other hand, located at the right side of the triangle where the AB line will be the base line for C. The scale for C will be situated in between the BC line.


When there is third component is added to a pair of miscible liquid, it may affect the mutual solubility. If the third component is more soluble in one of the liquids than the other, then the miscibility between the pair of liquids decreases. Conversely, if the third component is soluble in both components, the mutual solubility will increase.

Experimental method

Apparatus
1.      Conical flask
2.      Burette
3.      Retort stand
4.      Funnel
5.      Measuring cylinder
6.      Droppers

Materials
1.      Ethanol
2.      Toluene
3.      Distilled water 

Experimental Procedure
    1. Eight conical flasks containing 20 ml of ethanol and toluene are prepared with the following percentage of ethanol act as the analyte 
      Percentage of ethanol (%)
      Volume of ethanol (ml)
      Percentage of toluene (%)
      Volume of toluene (ml)
      10
      2
      90
      18
      25
      5
      75
      15
      35
      7
      65
      13
      50
      10
      50
      10
      65
      13
      35
      7
      75
      15
      25
      5
      90
      18
      10
      2
      95
      19
      5
      1
    2. A burette filled with distilled water is prepared as the titrant  and the apparatus and materials are set up as shown in the diagram below
    3. Each mixture is titrated with water and shaken well until cloudiness is observed as a result of the existence of a second phase.
    4.  Volume of the water is recorded as the mixture turns cloudy.
    5.  The temperature of the room is recorded which is 27.9°C
    6.  The new percentage of each component based on its volume is calculated and recorded in the table as the second phase starts to appear/separate.
    7.  The points are plotted onto the triangular paper given to give a triple phase diagram at the recorded temperature.
    8.  Step 1-7 is repeated twice to obtain the average results.

Results and Calculation

Discussion
Phase diagram can be defined as graphical representation of liquid, vapour and solid phases that co-exist together at various range of temperature as well as pressure. On the other hand, ternary phase diagram represents the phase behaviour of mixture containing three components in a triangular diagram. In this experiment at the temperature of 27.9°C, the three components contained in the ternary diagram are water, toluene and ethanol. Water is used as the third component as it was titrated into the mixture of 20 ml of toluene and ethanol. Water is added until cloudiness of the mixture appeared. Therefore, the volume of water required to turn the mixture cloudy is recorded. Noted that the appearance of cloudy mixture indicates that second phase is present.

Figure shows the ethanol-toluene-water system

In the ternary graph plotted, the region above the curve represents the one-phase mixture solution while the region under the curve depicts the two-phase mixture solution. At the beginning of the experiment, toluene and ethanol are mixed together based on the percentage of ethanol provided in the table above. As both of the liquid are mixed together, it formed a one-phase mixture solution as ethanol is soluble in toluene. However, as water is titrated, it disrupts the mutual solubility of a pair of miscible liquids. Keep in mind that ethanol is soluble in water while toluene is insoluble in water. If the third component is more soluble in one of the two different component mixture, the mutual solubility decreases, thus two phase liquid appear. Therefore, as water is added, the mutual solubility keep on decreasing until it reaches a point where the mixture become separated (two phase solution). In the end of the experiment this theory is proven as more of water titrated into the mixture, cloudy immiscible solution appeared. In addition, all of the components in this experiment can become a miscible solution when they are mixed together if and only if proportion of each component is determined.

Figure depicts the material used during the experiment
In order to describe the one phase system completely, a maximum of four intensive variables (degree of freedom) must be fixed, F=3-1+2=4. The system is becoming more complex if the degree of freedom increases as more variable is required to be fixed in order to define the system. According to the phase rule, a single phase in a three-component system may possess four degrees of freedom. In the beginning of the experiment, the degree of freedom, F comprised of temperature, pressure and the each of the concentration of the components. As water is titrated, F is reduced to 2 (F=3-2+2) as number of component increases and the number of phase decreases.

There are few errors in the experiment that affect the results of this experiment. One of it is the apparatus used in this experiment may be contaminated with the remnant of distilled water used to rinse the apparatus. This may affect the result of the initial mixture (ethanol and toluene) as water is already present in the mixture at the first place. Aside from that, the source of contamination is that the materials are exposed to air as the apparatus is not covered up. Next, errors in reading the volume of water to titrate the solution by using burette may occur as the eye level is not perpendicular to the meniscus of the burette. Besides, error may occur during the preparation of the mixture. Less or extra volume of either ethanol and toluene prepared as well as the volume of water titrated (the cloudiness may have change earlier than the volume observed).

Therefore, in order to reduce the error, the apparatus need to be well cleaned and dried up to avoid the early present water in the solution. The apparatus need to be covered up with cork in order to avoid reaction with air and disrupts the experiment. Next, when reading the volume of water titrated by using burette, ensure the eye level is perpendicular to the meniscus of the burette in order to obtain accurate reading. Extra precaution should be taken during the preparation of solution to obtain the accurate volume of liquid based on the procedure. Last, it is suggested that only one person controls the titration to avoid any delayed in closing the burette as the solution turns cloudy. 


Conclusion

In this experiment, ethanol and toluene are a pair of miscible liquids, but when water is added to the ethanol-toluene system as the third component, it will change their mutual solubility. This is because water only soluble in ethanol and it will make the mutual solubility of the liquid pair decrease. Therefore, the system will form two-phase system. When sufficient toluene and ethanol was added to the ternary system, all the components will form a miscible liquid. However, this does not apply when we increase the amount of water to the system.

Practice


1. Does the mixture containing 70% ethanol, 20% water and 10% toluene (volume) appear clear or does it form two layers?

Based on the phase diagram, at point where the mixture containing 70% ethanol, 20% water and 10% toluene will appear clear and form only one layer.

2. What will happen if you dilute 1 part of the mixture with 4 parts of (a) water
(b) toluene (c) ethanol?

·               1 part of 70% of ethanol: (1 part x 70/100) = 0.7 of ethanol
·               1 part of 20% of water: (1 part x 20/100) = 0.2 of water
·               1 part of 10% of toluene: (1 part x 10/100) = 0.1 of toluene

⸫ There will be 0.7 of ethanol, 0.2 of water and 0.1 of toluene in the mixture.

a) 1 part of the mixture diluted with 4 parts of water:

Ethanol: (0.7 / 1+4) x 100% = 14%
Water: (0.2 + 4) / (1+4) x 100% = 84%
Toluene: (0.1 / 1+5) x 100% = 2%

Based on the phase diagram, two phases and two layers will form at point where the mixture containing 14% of ethanol, 84% of water, and 2% of toluene.

b) 1 part of mixture diluted with 4 parts of toluene:

Ethanol: (0.7 / 1+4) x 100% = 14%
Water: (0.2 /1+4) x 100% = 4%
Toluene: (0.1 + 4) x 100% = 82%

Based on the phase diagram, single phase and one layer will appear at point where the mixture containing 14% of ethanol, 4% of water, and 82% of toluene.

c) 1 part of mixture diluted with 4 parts ethanol:

Ethanol: (0.7 + 4 / 1+4) x 100% = 94%
Water: (0.2 / 1+4) x 100% = 4%
Toluene: (0.1 / 1+4) x 100% = 2%


Based on the phase diagram, a single phase and one layer will form at point where the mixture containing 94% of ethanol, 4% of water, and 2% of toluene.

Reference
Adam Skrzecz, D. S. (1998). 4.6. Etahnol + Water +Toluene. In D. S. Adam Skrzecz, IUPAC-NIST Solubility Data Series 69. Ternary Alcohol-Hydrocarbon-Water System (pp. 1059-1069). Poland: National Institute of Standards of Technology.
Campbell, F. (2012). Ternary Phase Diagrams. In F. Campbell, Phase Diagrams-Understanding the Basics (pp. 191-200). ASM International.
CSUN. (2010, April 12). Experiment 5: Phase diagram for a three-component system. Retrieved from California State University, Northridge: https://www.csun.edu/~jeloranta/CHEM355L/experiment5.pdf



c

No comments:

Post a Comment

Powered by Blogger.
Physicochemical Properties of Drugs © , All Rights Reserved. BLOG DESIGN BY Sadaf F K.