Title:
Determination of Phase Diagram for Ethanol/Toluene/Water
System Theory
Three-Component Systems
Date of Practical
10 November 2016
Objective
- To determine the limit solubility of water and two other liquids which are ethanol and toluene (methylbenzene) in a ternary system
- To construct a phase diagram of ethanol/toluene/water system
Introduction
In system
containing three components but only 1 phase, the degree of freedom will be
four which are temperature, pressure, and the concentration of two or the three
components. The degree of freedom, F can be calculated using
the formula (phase rule) given:
F = C - P + 2
Where,
C = the
number of components
In the above diagram, it shows the ternary
diagram. The three apexes representing a 100% pure composition and they are labelled A, B, and C. By referring to diagram below,
the nearest to the head of the red arrow indicates 100% of A while the farthest
from A represents 0% of A. Other values besides 0% and 100% can be indicated by
the line between 0% to 100%. The right side of the triangle will be the scale
for the percent abundance of A component.
Point B located at the left side apex of the triangle.
The apex indicates 100% of B component. The AC line will be the base line for
B. The scale of the percentage abundance of B will be at the left side of the
triangle.
Point C on the other hand, located at the right side
of the triangle where the AB line will be the base line for C. The scale for C
will be situated in between the BC line.
When there is third component is added to a pair of
miscible liquid, it may affect the mutual solubility. If the third component is
more soluble in one of the liquids than the other, then the miscibility between
the pair of liquids decreases. Conversely, if the third component is soluble in
both components, the mutual solubility will increase.
Experimental method
Apparatus
1. Conical
flask
2. Burette
3. Retort
stand
4. Funnel
5. Measuring
cylinder
6.
Droppers
Materials
1. Ethanol
2. Toluene
3.
Distilled water
Experimental Procedure
- Eight conical flasks containing 20 ml of ethanol and toluene are prepared with the following percentage of ethanol act as the analyte Percentage of ethanol (%)Volume of ethanol (ml)Percentage of toluene (%)Volume of toluene (ml)10290182557515357651350105010651335775152559018102951951
- A burette filled with distilled water is prepared as the titrant and the apparatus and materials are set up as shown in the diagram below
- Each mixture is titrated with water and shaken well until cloudiness is observed as a result of the existence of a second phase.
- Volume of the water is recorded as the mixture turns cloudy.
- The temperature of the room is recorded which is 27.9°C
- The new percentage of each component based on its volume is calculated and recorded in the table as the second phase starts to appear/separate.
- The points are plotted onto the triangular paper given to give a triple phase diagram at the recorded temperature.
- Step 1-7 is repeated twice to obtain the average results.
Results and Calculation
Discussion
Phase diagram can be defined as graphical
representation of liquid, vapour and solid phases that co-exist together at various
range of temperature as well as pressure. On the other hand, ternary phase
diagram represents the phase behaviour of mixture containing three components
in a triangular diagram. In this experiment at the temperature of 27.9°C, the
three components contained in the ternary diagram are water, toluene and
ethanol. Water is used as the third component as it was titrated into the
mixture of 20 ml of toluene and ethanol. Water is added until cloudiness of the
mixture appeared. Therefore, the volume of water required to turn the mixture
cloudy is recorded. Noted that the appearance of cloudy mixture indicates that
second phase is present.
In the ternary graph plotted, the region above the
curve represents the one-phase mixture solution while the region under the
curve depicts the two-phase mixture solution. At the beginning of the
experiment, toluene and ethanol are mixed together based on the percentage of
ethanol provided in the table above. As both of the liquid are mixed together,
it formed a one-phase mixture solution as ethanol is soluble in toluene.
However, as water is titrated, it disrupts the mutual solubility of a pair of
miscible liquids. Keep in mind that ethanol is soluble in water while toluene
is insoluble in water. If the third component is more soluble in one of the two
different component mixture, the mutual solubility decreases, thus two phase
liquid appear. Therefore, as water is added, the mutual solubility keep on
decreasing until it reaches a point where the mixture become separated (two
phase solution). In the end of the experiment this theory is proven as more of
water titrated into the mixture, cloudy immiscible solution appeared. In
addition, all of the components in this experiment can become a miscible
solution when they are mixed together if and only if proportion of each
component is determined.
![]() |
| Figure depicts the material used during the experiment |
In order to describe the one phase system completely, a
maximum of four intensive variables (degree of freedom) must be fixed,
F=3-1+2=4. The system is becoming more complex if the degree of freedom
increases as more variable is required to be fixed in order to define the
system. According to the phase rule, a single phase in a three-component system
may possess four degrees of freedom. In the beginning of the experiment, the
degree of freedom, F comprised of temperature, pressure and the each of the
concentration of the components. As water is titrated, F is reduced to 2
(F=3-2+2) as number of component increases and the number of phase decreases.
There are few errors in the experiment that affect the
results of this experiment. One of it is the apparatus used in this experiment
may be contaminated with the remnant of distilled water used to rinse the
apparatus. This may affect the result of the initial mixture (ethanol and
toluene) as water is already present in the mixture at the first place. Aside
from that, the source of contamination is that the materials are exposed to air
as the apparatus is not covered up. Next, errors in reading the volume of water
to titrate the solution by using burette may occur as the eye level is not
perpendicular to the meniscus of the burette. Besides, error may occur during
the preparation of the mixture. Less or extra volume of either ethanol and
toluene prepared as well as the volume of water titrated (the cloudiness may
have change earlier than the volume observed).
Therefore, in order to reduce the error, the apparatus
need to be well cleaned and dried up to avoid the early present water in the
solution. The apparatus need to be covered up with cork in order to avoid
reaction with air and disrupts the experiment. Next, when reading the volume of
water titrated by using burette, ensure the eye level is perpendicular to the
meniscus of the burette in order to obtain accurate reading. Extra precaution
should be taken during the preparation of solution to obtain the accurate
volume of liquid based on the procedure. Last, it is suggested that only one
person controls the titration to avoid any delayed in closing the burette as
the solution turns cloudy.
Conclusion
In this experiment, ethanol and toluene are a pair of
miscible liquids, but when water is added to the ethanol-toluene system as the
third component, it will change their mutual solubility. This is because water
only soluble in ethanol and it will make the mutual solubility of the liquid pair
decrease. Therefore, the system will form two-phase system. When sufficient
toluene and ethanol was added to the ternary system, all the components will
form a miscible liquid. However, this does not apply when we increase the
amount of water to the system.
Practice
1. Does the mixture containing 70%
ethanol, 20% water and 10% toluene (volume) appear clear or does it form
two layers?
Based on the phase diagram, at point where the mixture
containing 70% ethanol, 20% water and 10% toluene will appear clear and form
only one layer.
2. What will happen
if you dilute 1 part of the mixture with 4 parts of (a) water
(b) toluene (c) ethanol?
(b) toluene (c) ethanol?
·
1 part of
70% of ethanol: (1 part x 70/100) = 0.7 of ethanol
·
1 part of 20%
of water: (1 part x 20/100) = 0.2 of water
·
1 part of 10%
of toluene: (1 part x 10/100) = 0.1 of toluene
⸫ There will be 0.7 of ethanol, 0.2 of
water and 0.1 of toluene in the mixture.
a) 1 part of the mixture diluted with 4
parts of water:
Ethanol: (0.7 / 1+4) x 100% = 14%
Water: (0.2 + 4) / (1+4) x 100% = 84%
Toluene: (0.1 / 1+5) x 100% = 2%
Based on the phase
diagram, two phases and two layers will form at point where the mixture containing
14% of ethanol, 84% of water, and 2% of toluene.
b) 1 part of mixture diluted with 4 parts of
toluene:
Ethanol: (0.7 / 1+4) x 100% = 14%
Water: (0.2 /1+4) x 100% = 4%
Toluene: (0.1 + 4) x 100% = 82%
Based on the phase
diagram, single phase and one layer will appear at point where the mixture
containing 14% of ethanol, 4% of water, and 82% of toluene.
c) 1 part of mixture diluted with 4 parts
ethanol:
Ethanol: (0.7 + 4 / 1+4) x 100% = 94%
Water: (0.2 / 1+4) x 100% = 4%
Toluene: (0.1 / 1+4) x 100% = 2%
Based on the phase
diagram, a single phase and one layer will form at point where the mixture
containing 94% of ethanol, 4% of water, and 2% of toluene.
Reference
Adam Skrzecz, D. S. (1998). 4.6.
Etahnol + Water +Toluene. In D. S. Adam Skrzecz, IUPAC-NIST Solubility Data
Series 69. Ternary Alcohol-Hydrocarbon-Water System (pp. 1059-1069).
Poland: National Institute of Standards of Technology.
Campbell, F. (2012). Ternary Phase
Diagrams. In F. Campbell, Phase Diagrams-Understanding the Basics (pp.
191-200). ASM International.
CSUN. (2010, April 12). Experiment
5: Phase diagram for a three-component system. Retrieved from California
State University, Northridge: https://www.csun.edu/~jeloranta/CHEM355L/experiment5.pdf
c





