20/12/2016

Practical 4: Particle Size Analysis (Part A)

Objectives :
  • To determine the particle size distribution of lactose and microcrystalline cellulose (MCC) by using sieving method.

Introduction
Sieves are used to break down agglomerates and sieve analysis is a procedure to determine the size and size distribution of a particular powder or any granular material. It can be performed on any type of non-organic or organic materials such as sands, clays, granite, lactose or microcrystalline cellulose (MCC) depending on the exact method. The size distribution is often of critical importance to the way the material performs in use. In this experiment, sieve nest is used to determine the particle size and the size distribution of lactose and MCC. Sieve nest which consist of different diameters are stack in graded. This mechanical sieve will then start sieving depends on the time needed. 



Procedure :

1. 100 g of lactose is weighed.
2. The sieve nest is prepared in descending order from the largest diameter on top to the smallest (bottom).
3. The powder is placed at the uppermost sieve and the sieving process is allowed to proceed for 20 minutes.
4. The powder collected at every sieve is weighed and the particle size distribution is plotted in the form of histogram.
5. The process is then repeated using microcrystalline cellulose (MCC). 


Result :
        
        a)      Lactose

        b)      Microcrystalline cellulose (MCC)


Discussion :


Sieve nest is an apparatus that being used to undergo sieving analysis. Sieving is a process to determine the size of distribution of a granular material. It is important to determine the materials’ size for them to perform their function which is commonly used in pharmaceutical field. However, sieving process is not only to determine the materials’ size for pharmaceutical products, even non-organic materials such as sand also can used this apparatus if the correct method is used. Sieve apparatus is prepared in descending order, from largest diameter to smallest diameter.
In this experiment, there were two materials being used, microcrystalline cellulose (MCC) and lactose. Both were placed at the uppermost of sieve apparatus, the sieving process was set up for 10 minutes and 20 minutes. After sieving process has stopped, there was some particles of MCC or lactose in each of sieve. The particles’ size was measured.
The result obtained for 10 minutes sieving was best illustrated by the graph. Based on the graph, the lactose size for is in between 601 μm to 710 μm to while the MCC size is in between 51 μm to 53 μm. As for the results for 20 minutes sieving of lactose and MCC, it shows that the lactose size is in between 54 μm to 150 μm. The MCC size is in between 50 μm and below.
Based on this size distribution, we can conclude that the lactose particles is more bigger than MCC particles as the distribution of lactose of 10 minutes and 20 minutes sieving can be seen mostly in sieve nest 600 μm and 53 μm respectively.
However, this result may not be exact due to some errors while conducting the experiment. This may caused by the blown out of the powder during the collecting process. Besides, there may be some left over of powders in between the sieve net. The particles may be clumped due to the moisture absorbed from the air. Therefore, precaution steps need to be taken to get an accurate result. We can use a closed container to collect the powder. We also need to transfer the powder to the sieve nest quickly and carefully so that they will not absorb the air moisture, results the clumping of the powders.


Conclusion :


In conclusion, the particle size distribution of lactose is much more bigger than the particle size distribution of microcrystalline cellulose (MCC). In the 10 minutes sieving lactose mostly collected in size between  601 μm to 710 μm while MCC collected in range 51 μm to 53 μm. As for the 20 minutes sieving lactose mostly collected in size between 54 μm to 150 μm while MCC collected in range 50 μm and below.  

Questions :

1.What are the average particle size for both lactose and MCC?

The average particle size for lactose in 10 minutes is in between 601 μm to 710 μm while in 20 minutes in between 54 μm to 150 μm.
The average particle size for MCC in 10 minutes is in between 51 μm to 53 μm while in 20 minutes in between 50 μm and below. 
  
2. What other methods can you use to determine the size of particles?

There are several types of methods to determine the size particles such as, microscope method, laser light scattering method, dynamic light scattering method and coulter counter.

3. What are the importance of particle size in a pharmaceutical formulation?

The particle size distribution is important to be determined especially the size of active ingredients and excipients. Their physical characteristic is used to create pharmaceutical products. The size, distribution and shape of the particles can affect bulk properties, product performance, processability, stability and appearance of the end product.


References :

1. Alfred.N Martin. 2006. Martin’s Physical Pharmacy and Pharmaceutical Sciences: Physical Chemical and Biopharmaceutical principles in the Pharmaceutical Sciences. Patrick J. Sinko, Yashveer 
2. Atwood. David, Alexander. T Florence. 2008. Physical Pharmacy Second Edition. Pharmaceutical Press.
3. https://en.wikipedia.org/wiki/sieve

No comments:

Post a Comment

< > Home
Powered by Blogger.
Physicochemical Properties of Drugs © , All Rights Reserved. BLOG DESIGN BY Sadaf F K.